With design, sustainability & quality running right to the core, there’s only one company we could work with on our valve colours - Chris King! With our valves for life guarantee and their stunning colourways, your bike is in for a real treat for years to come. Made from premium lightweight, high strength 7075 aluminium, Peaty’s MK2 Tubeless Valves fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims. Our unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, our valves have a ‘straight-through’ design so there’s no reduction of sealant or air flow when tyre inserts are not used. Fitting couldn’t be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails. Crushed a rubber or snapped an o-ring? No problem, check out our service kits to spruce up your valves when swapping to your next set of wheels or new bike. Instructions (1) Remove valve cap, o-ring and lock nut (2) Insert valve through valve hole in rim (3) Push the o-ring onto valve stem (4) Thread the lock nut onto valve stem (5) hand tighten lock nut until firm (6) Screw on valve cap

"Peaty's unique single-sided fork design allows for multiple plug sizes to be easily rolled into the dip of the fork and pushed straight into the tyre. The open side to the fork then allows for the tool to be easily pulled back out of the hole without pulling the plug out with it. Made from high quality 316 Stainless steel, the fork is designed to be as short as possible to reduce the chance of you puncturing your rim tape when inserting a plug. The fork has also been designed with a reaming texture on the shaft, to clean out punctures before plugging, and to be as slim as possible, so it doesn’t widen the size of the hole already there. Shrinking down to a tiny 65mm x 19mm, this tool has been designed to easily fit into your pocket or slot into a tool wrap or backpack. With knurling on the tool base and ribbing on the lid, you shouldn’t have any issues gripping the tool, even in the muddiest of conditions. Simply unscrew the lid and thread it onto the rear of the tool to make a sturdy handle to hold onto while inserting the plug. This pack includes three thick (3mm) plugs and three thin (1.5mm) plugs. These plug sheets can be neatly wrapped around the fork and stored neatly inside the compact water-sealed body. Holeshot refill plug sheets also sold separately packaged with cardboard header cards & in biodegradable bags. KEY FEATURES - Available in 12x Chris King colours - Quick and easy to insert tyre plugs. With our unique single-sided fork design, you simply push and roll the plug into the hook of the fork - With no tight gap to squeeze through, the plug is far less likely to pull back out when the tool is extracted the fork is sharp tipped & as slim as possible so it doesn’t widen the size of the - hole already there - Fork made from 316 stainless steel - Body made from anodised 6061 aluminium - Knurled body and ribbed lid / handle for extra grip - Weather sealing o-rings make the tool waterproof when assembled - Each kit comes with one sheet of 3x 1.5mm and one sheet of 3x 3mm plugs"

- Available in 1.5mm & 3mm plug sizes. - 6 plugs per pack, in 2 sheets of 3 plugs - Designed to fit perfectly into the body of Peaty’s Holeshot Tyre Puncture Plugger tool - Packaged using recycled cardboard header cards and biodegradable bags

With design, sustainability & quality running right to the core, there’s only one company we could work with on our valve colours - Chris King! With our valves for life guarantee and their stunning colourways, your bike is in for a real treat for years to come. Made from premium lightweight, high strength 7075 aluminium, Peaty’s MK2 Tubeless Valves fit most tubeless setups from MTB to road and cyclocross, including carbon, enduro and DH rims. Our unique x-cut base has been designed to work with all tyre inserts. The channels cut into the base of the valve allow air and sealant to pass through when inserts are pushed up against them. Unlike most other insert-compatible valves, our valves have a ‘straight-through’ design so there’s no reduction of sealant or air flow when tyre inserts are not used. Fitting couldn’t be easier. integrated o-rings prevent the lock rings from scratching your precious rims and large soft rubber bases easily create an airtight seal. Designed by riders, for riders. Our valves come as standard with an integrated valve core remover cap and spoke key cap (for standard 3.4mm spoke nipples). This makes tightening loose spokes and topping up with sealant a breeze, either in the workshop or out on the trails. Crushed a rubber or snapped an o-ring? No problem, check out our service kits to spruce up your valves when swapping to your next set of wheels or new bike. Instructions (1) Remove valve cap, o-ring and lock nut (2) Insert valve through valve hole in rim (3) Push the o-ring onto valve stem (4) Thread the lock nut onto valve stem (5) hand tighten lock nut until firm (6) Screw on valve cap